Step 1: Chairs are not all created-or upholstered-equally
Here we’ll show you how to reupholster a chair with a ‘drop-in’ or ‘screw-on’ seat-a style shared by many benches and stools. Seat bases can be constructed from a variety of materials: solid wood, plywood, pegboard and others. The seats are normally screwed on but can also be glued on or dropped in. The cushions can be foam, cotton or other natural materials.
Which stapler works best?
All the staplers shown will do the trick. The question is: How hard do you want to work-and squeeze-to ‘do the trick’? Your stapler buying decision may also hinge on a few other factors, including how often you’ll use it, what else you might use it for-and whether you need a good excuse to buy an air compressor.
Step 2: Round up your materials
When you shop, buy ‘upholstery grade’ fabric for its strength and stain resistance. Fabric prices vary wildly; you might find something for $5 in the bargain bin or spend 10 times as much. We bought our fabric, foam and batting at a fabric store. For the dust cover, we used landscape fabric from a home center.
Step 3: Remove the old and get ready for the new
Photo 1: Remove the old upholstery
Pry and yank the staples with a screwdriver and pliers or side cutters. Remove the upholstery and cushion material.
Photo 2: Make a new seat
If the old seat is in bad shape, cut a new one from plywood. Trace around the old seat, then cut with a jigsaw or circular saw. Bevel or soften edges with a sander or router to match the old contour.
Photo 3: Cut the foam
Trace the outline of the seat onto 1-in.-thick foam. Cut the foam with a bread knife. To avoid tearing the foam, pull the knife toward you, using light pressure and short strokes.
Our seats, for example, were made from a pegboard-like material secured to a 1×3 framework, covered with horsehair padding. Someone had already reupholstered the chairs, going directly over the old fabric. Expect the unexpected and adjust your game plan accordingly.
If you’re re-covering more than one chair, number each chair and seat; that way, the screw holes will line up properly when you reinstall the seats. There are special tools just for yanking upholstery staples or tacks, but you can get by with basic hand tools (Photo 1). Tip: Old, dull side cutters are perfect. They grip staples well but don’t cut them off.
Remove the padding and inspect the seat. If the wood base seems solid, reuse it. If it’s cracked, use it as a template to make a new one (Photo 2). We used a sander to taper the edges to match the profile of the old one. Plop the seat on top of the foam and outline it with a marker. Use a serrated bread knife (Photo 3) to cut just inside the line.
Step 4: Install the new fabric
Photo 4: Add the batting
Cut the batting so it overhangs all sides of the seat by about 4 in. Then drive a single staple on each side to hold the foam in place.
Photo 5: Center the pattern
Determine the best layout for your material; make sure any patterns or stripes align correctly. Hang the edge of the seat over your work surface then drive a staple, from below, in the centers of the front and back.
Photo 6: Staple the front edge
Working from the center outward, install staples along the front as you lightly tension the material with your hand. Stop 2 in. from the corner. Flip the seat over several times to check the pattern as you go. Repeat the process along the back edge and sides.
Place a section of batting-4 in. wider in all directions than the size of your chair seat-on a flat work surface, then set your foam and seat on top. Lightly stretch the batting and drive one staple (Photo 4) along each edge.
Flip the seat over, then center your material on top (Photo 5). Cut the material so you’ll be able to wrap it up onto the chair bottom at least 4 in. in each direction. With the seat facing up and the front edge overhanging the work surface, drive one staple through the bottom to hold the material in place. Rotate the seat 180 degrees, then tack the back the same way.
Check your pattern alignment one more time, then flip the seat upside down. Starting at the front middle staple and working toward the corners, use the palm of your hand to lightly stretch the material, then drive a staple every 2 in. (Photo 6). Keep the staples within an inch of the edge, and secure the batting and fabric at the same time. Use your entire hand, not just fingertips, to tighten the material. This way you’ll avoid little dips and puckers in the pattern.
Repeatedly flip the seat over to check the pattern for straightness; it’s easier to keep flipping and checking than to go back and pull staples. Our expert flipped the seat over and checked the pattern a dozen times while stapling each edge. Stop stapling 2 in. from each corner. Secure the back edge in the same way, stretching the material lightly as you work. Then complete the sides, again repeatedly checking the pattern.
Step 5: Corners are the key
Photo 7: Trim the corners
Cut off the excess batting and upholstery so you don’t end up with ugly lumps at corners.
Photo 8a: Wrap the corners
Create a ‘butterfly corner’ by first tucking the center under, then folding and tucking the material to each side. Flip the seat over and drive staples to hold the corner tight.
Photo 9: Install the dust cover
After you trim the excess fabric and batting, staple on a dust cover-we used landscape cloth. A dust cover neatly hides the exposed fabric edges.
You can make simple, single-fold ‘hospital corners’ if the edges of your seat are concealed by a frame. But in most cases, the front corners will be exposed and will look better with a ‘butterfly corner.’
Remove excess batting and material from the corners (Photo 7) then flip the seat right side up and experiment with a few corner tucks. Fold the center inward, then overlap each side onto that fold (Photo 8). When the corner looks symmetrical and tight, flip the seat over and staple the folds in place.
When the corners are done, flip the seat over and cut off the excess material. Staple on a dust cover (Photo 9).
Required Tools for this Project
Have the necessary tools for this DIY project lined up before you start—you’ll save time and frustration.
- Basic hand tools
- Bread knife
- flat tip
- Small screwdriver
Required Materials for this Project
Avoid last-minute shopping trips by having all your materials ready ahead of time. Here’s a list.
- 1" x 24" x 24" high-density foam
- 1/2" to 3/4" plywood (if needed)
- 24" x 24" landscape fabric (optional)
- 30" x 30" quilt batting
- 30" x 30" upholstery fabric
- Upholstery staples