The pocket screw system and the key tools
Special drill bit
The pocket screw drill bit is stepped to simultaneously drill two different diameter holes. The stop color is the depth adjustment.
Don’t be put off by projects that call for tight joints or simple cabinet building. The pocket screw system is so easy to use that even a novice woodworker can make strong, tight joints on the first try. It works like this: You clamp the pocket hole jig onto your workpiece and drill angled holes with the special stepped drill bit. Then you simply align the two pieces to be joined and drive a pocket screw at an angle into the pocket to connect your pieces. The result is a tight joint that’s as strong as a doweled or mortise-and-tenon joint but takes a fraction of the time to assemble.
In this article, we’ll show you how to set up the jig and assemble joints using pocket kreg screws. We’ll show you techniques for assembling a face frame and a table leg and apron and for attaching shelf nosing. Refer to the instructions that came with your jig for ideas for other types of joints.
Buy a top-quality jig. Less-expensive jigs that lack built-in clamps or alignment guides aren’t worth messing with. The Kreg screws Rocket jig is a great mid-priced tool. The kit includes everything you’ll need to get started: a pocket hole jig, a special stepped drill bit and stop collar, a 6-in. driver bit, a locking pliers–type clamp and a handful of pocket screws. Buy Kreg screws jigs at woodworking stores or on-line, or shop for a high-quality pocket hole jig with similar features.
Video: How to Use a Pocket Screw Jig in Woodworking Projects
Pocket screws are a good way to put woodworking projects together. Jeff Gorton, an editor at We do everything by our own hands, shows you how to use a $40 kreg pocket screw jig (Kreig jig) that makes using pocket screws to assemble woodworking projects very easy.
Step 1: Drill the pocket screw hole
Photo 1: Set the drill bit depth
Tighten the stop collar onto the shank of the stepped drill bit. Leave a 1/8-in. space between the tip of the bit and the built-in stop on the end of the pocket hole jig.
Photo 2: Square board edges and ends
Check to make sure the edges of the boards are square to the face. Also check the end cuts to make sure your miter box is properly adjusted to make perfectly square cuts.
Photo 3: Clamp and drill
Slide the stop against the end of the board, center it and clamp the pocket hole jig in place. Bore two pocket holes for the screws. When you’re building a cabinet face frame like this, drill the pockets parallel to the grain of the wood as shown.
Pocket screw jigs are ready to go right from the package. All you have to do is slide the stop collar over the bit, adjust the bit depth and tighten the collar (Photo 1). The jig is initially set up for joining 3/4-in. material with 1-1/4 in. screws. Add the plastic spacer included with the Kreg Screws Rocket and use 2-1/2 in. long pocket screws to join 1-1/2 in. thick material like 2x4s. To join 1/2-in. thick material, reverse the stop on the front of the jig (refer to the instructions included with the kreg pocket hole jig) and use 1-in. long screws.
Photo 3 shows how to mount the jig and drill holes. Put the bit in the guide before you start the drill. Let the bit come to full speed before you push it into the wood. Withdraw the bit once or twice to eject shavings. It keeps the bit cooler and makes hole drilling easier.
Step 2: Drive the screw
Photo 4: Face frame technique
Position face frames precisely (use a spacer block here) and clamp the joint to hold the faces flush. Drive the pocket screws into the holes with the 6-in. long square driver bit until the joint is snug. Adjust the clutch on your drill to avoid overdriving the screw.
Photo 4A: Pocket Kreg screws
Pocket screws have special heads and shanks for drawing two boards together tightly.
Photo 5: Cabinet box technique
Assemble cabinet boxes with pocket screws by using the jig and drilling pocket holes every 8 to 12 in. along the edge of the plywood. Then glue, align and clamp the parts and screw them together. For a neater appearance, buy custom-shaped wood plugs to fill the pocket holes.
Photo 6: Offset technique
To hold table legs in place while you attach the apron with pocket screws, build a simple right-angle jig as shown. Place spacers behind the apron boards as shown to create the desired offset.
Photo 7: Shelf nosing technique
Drill pockets along the edge of the plywood shelf. Clamp shelf nosing to a perfectly flat surface like the table saw top shown here. Spread a thin layer of glue along the edge of the plywood and screw the plywood to the shelf nosing. The pocket screws will draw the plywood down, resulting in a flush joint when you flip the shelf over.
Pocket hole Screws (Photo 4A) cost a little more, but they have three features that make them uniquely suited for pocket hole joinery: First, the self-drilling tips will easily penetrate even the hardest wood. Second, the heads are extra strong and have a square recess for slip-proof driving. For hardwood lumber, use fine-thread screws; for softer woods like pine, choose coarse-thread screws. And third, the washer head helps prevent overdriving the screws when you’re joining particleboard or plywood.
There are a variety of screws available for specific applications. To check out the various types, order an assortment from the Kreg screws Co and check out these kreg pocket hole jig.
Hold the faces flush, then screw them together
Other than making sure your cuts are perfectly square, the only trick to getting flush, tight-fitting joints is keeping the faces lined up as you drive the screws. I’ve had great success using the locking pliers–type clamp included with the Kreg Rocket (Photo 4). Put the large round metal pad against the visible side of the joint and clamp the pieces together. The clamp holds the pieces in alignment while the screws pull the joint tight. Other pocket hole jig users I’ve talked to prefer to clamp both pieces down to a flat surface. Try it both ways and decide for yourself.
Even though it’s not necessary for a strong joint, it’s good insurance to spread a thin layer of wood glue over both surfaces before screwing them together.
Pocket screws have some limitations
Most people are amazed at how easy it is to assemble strong, tight-fitting joints with pocket screws. But because the pocket holes are apparent even when they’re filled, pocket screws aren’t the best choice for assembling cabinet doors or other projects where both sides of the joint show. Despite this limitation, you’ll find plenty of uses for a pocket hole jig around your home shop.
Required Tools for this pocket hole jig Project
Have the necessary tools for this DIY project lined up before you start—you’ll save time and frustration.
- Combination square
- Drill/driver - cordless
- One-handed bar clamps
Required Materials for this pocket hole jig Project
Avoid last-minute shopping trips by having all your materials ready ahead of time. Here’s a list.
- Pocket screws