DIY how to fix a leaky faucet repair
Doing your own faucet repair may seem daunting, but once you learn the basics, modern faucets like a Moen faucet repair are fairly easy. In fact, the hardest step to fix a leaky faucet is usually finding the right replacement parts for fixes like a Moen faucet repair. In this article, we’ll tell you how to find replacement parts for something like a Moen kitchen faucet repair and show you how to stop spout drips on the three main types of single-lever faucets: rotary ball, cartridge and ceramic disc. We’re showing kitchen faucets and kitchen faucet repair for a dripping faucet, but you can fix most single-lever bathroom faucets using the same procedures. We’ll also show you how to stop leaks around the base of the spout and fix leaking faucets.
The tools you’ll need for this how to fix a leaky faucet project vary a little depending on the faucet you’re repairing. You’ll probably need an Allen wrench to remove the handle. Buy a set of small Allen wrenches, and you’ll be prepared for all kinds of leaking faucets. Most repairs also require screwdrivers and a large slip-joint pliers.
Follow These Basics For All Faucet Repairs
Before you start, examine the dripping faucet closely to determine where the water is coming from. Leaks around the base of the spout require a different repair than a drip from the end of the spout.
Then turn off the water supply to the dripping faucet. You’ll probably find shutoff valves under the sink. If those valves don’t work or if you don’t have any, you’ll have to close the main water valve to your entire home. After you turn off the water, open the faucet in the center position to relieve water pressure and make sure the water is shut off. Finally, cover the sink drain holes with strainer baskets or rags to avoid losing small parts down the drain.
Pay close attention to the order and orientation of parts as you remove them. A digital camera or video camera is handy for recording each step in case you forget. For easier reassembly, set the parts aside in the order they were removed. When all the parts are out, inspect the interior of the valve for bits of deteriorated gaskets or mineral deposits. Use a cloth or fine nylon abrasive pad to clean the surface. Loosen mineral deposits by soaking them in vinegar.
Slow water flow can be caused by plugged holes in the faucet body. Use a small screwdriver or penknife to clean them out. Before you replace worn parts and reassemble the faucet, hold a rag over the dripping faucet and open the water shutoff valve slightly to flush out debris that may have been loosened during the cleaning and inspection.
After the faucet is reassembled, open the faucet to the middle position and gradually open the shutoff valves to turn on the water. Leave the faucet open until water flows freely and all the air is out of the pipes. If the water flow through the faucet is slow, the aerator (Figure A) may be plugged. Unscrew the aerator and clean it out.
Take the Old Parts to the Store to Find Replacements
You’ll often find the brand name stamped on the faucet. And this information will help when it comes time to find repair parts. But in most cases, the safest bet is to take the worn parts to the store with you.
If you have a Delta or other rotary ball faucet (Figure A), you’re in luck because you’ll find repair kits in most hardware stores and home centers. Cartridges and repair kits for Moen “cartridge type” (Figure B) faucets are also readily available. But if you have another brand or a disc-type faucet, you may have to order parts, since there are too many variations for most stores to keep in stock. It helps to know the faucet’s model name or number when searching for a replacement cartridge. Otherwise, take the cartridge with you to the store so you can match it to a photo in the parts catalog.
Plumbing supply specialists are also a good source of repair parts. If you’re having trouble finding parts, call the manufacturer of your faucet for help.
How to fix a leaky faucet: Rotary ball faucets
Figure A: Ball faucet parts
How rotary ball faucets are assembled.
How to fix a leaky faucet handle Step 1: Loosen the Allen screw
Photo 1: Lift the handle and pry off the decorative cover to expose the Allen screw. Turn the screw counterclockwise until it’s loose enough to lift the handle up from the stem.
How to fix a leaky faucet handle Step 2: Remove the cap
Photo 2: Unscrew the cap by turning it counterclockwise with a slip-joint pliers.
How to fix a leaky faucet handle Step 3: Remove the rotary ball
Photo 3: Lift off the plastic cam and packing. Lift out the ball and inspect it. Replace the ball if it’s scratched, cracked or visibly worn.
How to fix a leaky faucet handle Step 4: Remove the seats and springs
Photo 4: Lift out the two rubber seats and springs with a screwdriver. Make note of the orientation of the tapered spring and install the new springs and seats the same way. Reassemble the faucet.
Water flow and temperature in a rotary ball faucet are controlled by a hollow ball that rotates in a socket (Figure A). Delta and Peerless are two of the major brands. Your dripping faucet may have a brass or plastic ball. Both work well, although the long-lasting stainless steel ball comes with most repair kits. We recommend that you buy a repair kit that includes the ball, springs, seats and O-rings for the spout, as well as a small repair tool. With this kit, you’ll be prepared for almost any repair.
If water is leaking out around the base of the faucet handle, you may be able to fix the leak by removing the handle (Photo 1) and simply tightening the adjusting ring slightly (Figure A; a large version is available in the Addendum at the end of this article). Turn it clockwise with the spanner tool included in the repair kit. If the faucet drips from the end of the spout, replace the seats and springs (Photo 4).
Reassembly is straightforward in Delta kitchen faucet repair and other models. Drop the springs in the recesses and press the rubber seats over the top with your fingertip. Then align the groove in the ball with the pin in the socket and drop the ball in. Align the lug on the plastic cam with the notch in the valve body and set it over the ball. Thread on the cap with the adjusting ring and tighten it with the slip-joint pliers. Now you can turn on the water to check for leaks. If water leaks from around the ball stem, use the spanner tool to tighten the adjusting ring until the leak stops. Replace the leaking faucet handle and you’re done.
Figure B: Cartridge faucet parts
How cartridge-style faucets are assembled.
Step 1: Remove the allen screw
Photo 1: Pry off the handle cap (gently) with a knife. Turn the Allen screw counterclockwise to remove it and lift off the handle.
Step 2: Remove the metal handle adapter
Photo 2: Unscrew the dome assembly under the handle. Then unscrew the metal handle adapter and lift it off. Lift off the plastic pivot stop.
Step 3: Take out the retainer nut
Photo 3: Remove the retainer nut by turning it counterclockwise with large slip-joint pliers.
Step 4: Remove the retainer clip
Photo 4: Pry out the brass retainer clip with the tip of a screwdriver. Grab the clip with pliers and pull it the rest of the way out to avoid losing it.
Step 5: Twist loose the cartridge
Photo 5: Loosen the cartridge by slipping the plastic spanner cap (included with the new cartridge) over the cartridge and twisting it back and forth.
Step 6: Replace worn parts and reassemble the faucet
Photo 6: Grab the cartridge stem with pliers and pull it straight up and out. Replace worn parts and reassemble the faucet in the reverse order.
Many faucet brands use a cartridge of some type (Figure B, a large version is available in the Addendum at the end of this article). We show how to replace a Moen cartridge, but the process is similar for other brands. To stop drips at the spout or correct problems with hot and cold mi, remove the cartridge and either replace the O-rings on the cartridge if they’re worn or replace the entire cartridge. Take the cartridge to the home center or hardware store to find a replacement.
Photos 1 – 6 show how to remove the cartridge. Replacement cartridges for Moen faucets include a plastic spanner cap that allows you to twist and loosen the cartridge to make it easier to pull out (Photo 5). Don’t be surprised if the cartridge seems stuck. It may take considerable force to pull it out. Really stubborn cartridges may require the use of a special cartridge-pulling tool.
Reassemble the faucet in the reverse order. Pull the stem up before inserting the cartridge. You may have to twist the cartridge slightly to line it up for the brass retainer clip. Use the plastic spanner cap or the tips of needle-nose pliers to rotate the cartridge. Slide the brass clip into the slots in the valve body to hold the cartridge in place.
Look for the small notch on top of the stem and rotate the stem until the notch faces you (Photo 4). Install the remaining parts and reattach the handle. The directions that come with the stem will help orient you here. Then test the faucet. If the hot and cold water are reversed, simply remove the handle, dome assembly and handle adapter and rotate the stem 180 degrees.
Ceramic disc faucets
Figure C: Ceramic faucet parts
How ceramic disc faucets are assembled.
Step 1: Unscrew the handle
Photo 1: Pry off the decorative screw cover with your fingernail or the tip of a knife. Unscrew the handle screw by turning it counterclockwise with an Allen wrench. Lift off the handle. Unscrew or unclip the cap.
Step 2: Remove the disc cartridge
Photo 2: Remove the screws that hold the disc cartridge to the faucet body and lift out the cartridge.
Step 3: Replace the seals in the cartridge
Photo 3: Inspect the cartridge for mineral buildup and carefully clean it out. Then replace the rubber seals on the underside.
Step 4: Replace the o-ring seals
Photo 4: Lift out the plastic disc (on some faucets) and replace the O-rings under it. Inspect the holes in the faucet body and clean them out if they’re clogged.
Ceramic disc valves are simply another type of cartridge. Discs inside the cartridge control the water flow. This type of valve is sturdy and reliable and rarely needs fi. In fact, many manufacturers offer a lifetime guarantee on the cartridge. If yours is damaged, check with the manufacturer to see if it’s covered by a warranty.
Leaks can result from faulty rubber seals or a cracked disc inside the cartridge. Since it’s difficult to spot a cracked disc, and disc cartridge replacements are very expensive, it’s best to start by replacing the seals and reassembling the faucet. Then if the faucet still leaks, remove the disc cartridge and take it to the store to order a replacement.
Early versions of ceramic disc faucets may be more fragile and can crack if subjected to a blast of pressurized air. That’s why it’s important to leave the faucet open as you turn the water back on. This allows air trapped in the lines to escape. When the water runs smoothly, it’s safe to turn the faucet off. Manufacturers have improved the strength of ceramic discs on newer faucets to withstand air blasts, as well as abrasive debris that may get dislodged from the inside of pipes.
To see how a ceramic disc is assembled, see Figure C (a large version is available in the Addendum at the end of this article).
Step 1: Remove the spout to access the o-ring seals
Photo 1: Remove the handle and cartridge. Twist and pull up on the spout to remove it and expose the O-ring seals.
Step 2: Replace the o-rings
Photo 2: Slip the tip of a screwdriver under the O-rings to slide them out of the groove. Install the new O-rings, lubricate them with plumber’s grease and reinstall the spout.
Leaks around the base of the spout are caused by worn O-rings located under the spout. All that’s usually required to access these O-rings for replacement is to wiggle and pull up on the spout to remove it (Photo 1).
Depending on the dripping faucet, you’ll also have to remove the handle and other parts to access the spout. Be persistent. The spout may be a little stubborn. Spout O-ring kits are available for many faucets, or you can take the old O-rings to the hardware store or plumbing supply store and match them up with new ones. Remember to pick up a small toothpaste-type tube of plumber’s grease while you’re there.
In Photo 1, you can see the diverter valve, which controls water to the sprayer. Their appearance varies considerably among brands, but you’ll usually find them under the spout. If your sprayer isn’t working properly, first clean it in vinegar or simply replace it. If this doesn’t work, the diverter valve may be clogged. If it doesn’t simply pull out, the manufacturer or ask a knowledgeable salesperson for help with cleaning it.
Required Tools for this fi a leaking faucet project
Have the necessary tools for this how to fix a dripping faucet DIY project lined up before you start—you’ll save time and frustration.
- 4-in-1 screwdriver
- Allen wrench
- Slip joint pliers
Required Materials for this fi a leaking faucet project
Avoid last-minute shopping trips by having all your materials ready ahead of time. Here’s a list.
- Faucet repair kit
- O-ring seals