30 Cheap Kitchen Cabinet Add-Ons You Can DIY
These inexpensive, easy-to-build cabinet projects will help you take advantage of every nook and cranny of your kitchen storage space.
Lower Cabinet Rollouts
Vertical rollout drawers are a great way to convert a half-empty base cabinet into a high-capacity food storage cabinet that can be custom-sized to fit your storage needs. These drawers are easy to build yourself with these step-by-step plans.
Cutting Board with Storage: Instant Knife Rack
The Ultimate Container Storage Drawer
It’s always a challenge to find matching containers and lids. This rollout solves the problem by keeping them all neatly organized and easily accessible. The full-extension drawer slides are the key. To simplify tricky drawer slide installation, we’ve designed an ingenious carrier system that allows you to mount the slides and make sure everything is working smoothly before the unit is mounted in the cabinet. Get the full project plans here.
Build Classic Rollouts Plus a Trash Center
Under-Cabinet Wine Rack
Add a Shelf
Build Rollouts at Ankle Level
Look Up for Opportunities
Create an attractive display shelf for the empty space above your kitchen cabinets. This project requires only basic carpentry skills, and you can build it in a day. We’ll walk you through it step-by-step.
Cabinet Storage Organizers: Flip-Down Paper Tray
Build Rollouts in Underused Locations
Hidden Cutting Board
Make the metal plate under the cabinet larger than the cutting board so the board will be easy to put away. Glue the sheet metal to plywood with spray adhesive. Drill holes near the corners and screw it to the underside of a cabinet. Drill holes sized for the magnets and drop in a dab of super glue. Insert the magnets with a nail head. Slide the nail sideways to release the magnet. The metal plate grabs the magnets. Make sure you use galvanized steel, not aluminum. Plus, learn how to make your own cutting board!
Cutting Board Storage
Kitchen Cabinet Storage Organizers: Rollout Storage Panel
To install the panel in the cabinet, reassemble the slides. Hold the whole assembly against the cabinet wall and slide the panel out about 4 in. Drive screws through the cleats at the rear, then slide the panel out completely and drive screws at the front.
Kitchen Cabinet Dividers: Add a Divider for Upright Storage
Under-Sink Storage Bins
What’s hiding under your kitchen sink? If the space under your sink is anything like ours, it’s an overcrowded jumble of cleaning supplies, sponges and plastic bags. Here’s a great way to store these items right on the door of the sink cabinet. Cut a plastic storage tub in half with a utility knife and screw it to the inside of the cabinet door through the plastic lip at the top of the tub. Just make sure you position it so you can shut the cabinet door when all your bags and other supplies are in the bin.
Cabinet Drawer Organizer: Drawer in a Drawer
Cabinet Drawer Organizer: Rollout Drawer for Lids
Cabinet Door Storage Rack
Think Inside the Box
Building a slew of identical drawer boxes is easier, but having a variety gives you more versatility. Think about what you’re going to store and build the boxes to suit your needs.
Sloping sides: Rollout drawers with sloping sides keep tall things stable yet still let you see all the way to the back of the shelf. These are good for nesting pots and pans or storing different-size items on the same shelf.
Low sides: Lower sides (3 in. is typical) work well for smaller items such as canned goods and spices. The low sides make reading labels easier.
High sides: Shelves with higher sides all around (6 in. tall rather than the typical 3 in.) are ideal for tippy plastic storage containers or stacks of plates.
Kitchen Organization: Drop-Down Tablet Tray
Cutting Board Rack
You can make this nifty, inexpensive rack and mount it inside a cabinet door to stash your cutting board out of sight. It goes together in a snap since it only requires a 6-ft. 1×2 and two L-brackets.
Measure between the door stiles to get the maximum width of your rack. Make sure the rack will be wide enough for your cutting board (or spring for a new one). You’ll also need to mount the rack low enough so it doesn’t bump into a cabinet shelf when the door closes. Cut the bottom and face rails to match the space between the cabinet door stiles.
Cut the sides 7-1/4 in. long. Nail the sides to the base. Then nail the two face pieces at the top and bottom to complete the rack (photo, left). The easiest way to mount the rack is to take the cabinet door off its hinges and lay it down. Predrill the screw holes for the L-brackets and mount the rack to the cabinet door using a 1-in. L-bracket centered on each side of the rack (photo, right).
Measuring Cup Hang-Up
Build a Roll-Out Pantry Cabinet
The hardware consists of two heavy-duty bottom-mounted slides and one center-mounted top slide that together can support 130 lbs. Again, construct your unit to suit your needs. We made our bottom tray 3-1/2 in. tall and the upper ones 2-1/2 in. tall. You may want to include only two trays if you’ll be storing cereal boxes and other tall packages.
Since you’ll be converting your door from swinging to rolling mode, you’ll need to remove the door and hinges. You’ll also have to remove the existing handle and reinstall it centered on the door. If your hardware mounts from the backside, install it before attaching the door. Get the full instructions here.
Cabinet Door Message Board
A sheet of metal and a dry-erase board can turn any cabinet door into a convenient message center. You’ll find 2 x 2-ft. lengths of plastic-coated hardboard (often called ‘whiteboard’) and sheet metal at a hardware store or home center. Larger hardware stores will cut the sheet metal to your specifications. Be sure to get steel instead of aluminum so magnets will stick.
If you cut the metal yourself, wear gloves to protect your hands and use tin snips carefully. Use a metal file to smooth any ragged edges. If you don’t have a table saw to cut the whiteboard, flip it over, mark your measurements and use a jigsaw to cut it from the back to prevent chipping or splintering. To get a straight cut, use a framing square as a guide (photo, left).
To mount the metal sheet and whiteboard to the inside of the door, take the door off its hinges, lay it flat and carefully mask off the area where you want to spray the adhesive. Follow the directions on the can to apply the adhesive to the door, metal and whiteboard (photo, right). Mount the pieces, press firmly and let dry.
Storage Behind Closed Doors
Pegboard is great for organizing kitchens, laundry rooms and bathroom cabinets. Rout a groove in a 1×2 frame using a rabbet bit, attach the pegboard with glue and brads, then mount it to the door. The frame helps support the edges of the pegboard and creates a 1/2-in. space behind the board so pegs can be inserted.