Project overview: Benefits, materials and cost
This corner arbor turns empty space on a patio or deck into a leafy green sanctuary. Use it to create shade and privacy, to screen an unattractive view, or to add color to a concrete patio or wood deck—even a second floor deck. Our arbor is covered with a tropical vine called mandevilla, a great plant for walls, trellises and arbors.
The entire arbor is made from pressure-treated wood, but coating it with a penetrating stain and hiding the fasteners makes the project look more like a piece of furniture than decking. The stain will also help keep it from cracking and warping as it weathers.
Using pressure-treated wood keeps the cost reasonable too. All the materials for this project cost $250. The project can be built over two weekends—or one if you don’t stain it.
Treated wood lasts almost forever, but it can be gnarly to work with. Take your time picking through the lumber pile for good pieces. Look for dry (lighter) pieces without too many knots. You’ll need straight pieces for the uprights and benches, but you can use nice-looking, moderately warped pieces for the planters. Let the lumber sit for a few weeks so it all shrinks uniformly. Remember to put the best sides out when you assemble the planters and benches.
3 Simple Components: Trellises, Planters and Benches
To build this project, just cut lumber to length and screw the parts together. If you can handle a tape measure, a saw and a drill, you can do it. Customization is easy, too: Build shorter seats to suit a small space or add components to surround a big space. If you don’t need shade or privacy, leave off the trellis.
Step 1: Assemble the planter boxes
Photo 1: Cut the parts
Cut the planter box pieces and bench parts quickly and accurately using a stop block.Photo: Courtesy of We do everything by our own hands
Photo 2: Assemble the fronts and backs
Assemble the front and back of the planters against a square. Use spacer blocks to align the planter box corners perfectly.Photo: Courtesy of We do everything by our own hands
Photo 3: Add the box sides
Stand the front and back up, then attach the sides, screwing through the planter box corners. Predrill to avoid splits.Photo: Courtesy of We do everything by our own hands
Photo 4: Stain all parts
Stain the bench and trellis parts and the completed planter boxes before assembly to save time and mess.Photo: Courtesy of We do everything by our own hands
Each planter box is made by alternating 10 short and 10 long lengths of 2×4 and joining the inside corners with 2x2s. The overall size is based on 16-in. square plastic planters (actual size 15-1/2 in.) widely available at home centers. If you can’t locate that exact size or you prefer a different style, make the planter supports (D and E) larger or smaller, or build a base inside the planter box to support the planter. You can also change the size of the planter box.
Use a stop block to cut all the pieces quickly and accurately (Photo 1). Set three long and two short pieces against a square clamped to the worktable, using short spacer blocks for alignment. Predrill the 2×2 corners with a No. 8 countersink bit to avoid splitting the wood (Photo 2). One 2-1/2-in. screw per 2×4 is sufficient.
Make a front and back for each planter box, then set them upright and join them with interlocking 2×4 pieces (Photo 3), again attaching them from the inside. Although screwing from the inside is fussier, it enables you to avoid the cracks that often occur when pressure-treated wood is screwed near the ends.
Finally, screw the bench supports on (see Figure A in “Additional Information” below). Stain the planter boxes and all the other pieces now to avoid drips on the deck or patio. It’s also easier to coat all the bench pieces on all four sides at this stage (Photo 4).
Note: You can view and download the Cutting List, Materials List and Figure A in “Additional Information” below.
Step 2: Construct the benches
Photo 5: Assemble the benches
Clamp the bench front and bench end against a square corner. Screw the bench pieces together from the back to keep fasteners hidden.Photo: Courtesy of We do everything by our own hands
Photo 6: Connect the benches and planters
Set the benches on the bench supports, then fasten the planter boxes to the bench ends.Photo: Courtesy of We do everything by our own hands
Photo 7: Level the benches
Shim the planter boxes to level the benches. Install hidden legs to hold the planter level, then remove the shims.Photo: Courtesy of We do everything by our own hands
Clamp the front and one of the sides of the bench to a square edge. Clamp the first set of spacers and the first 2×4 slat to the front piece, then drive two 3-in. screws through the slat and the spacer into the front piece. Continue fastening, clamping the slats in position to keep them aligned before screwing them in (Photo 5). Check to make sure the bench stays flat as you assemble it. Toe-screw the bench ends to the front of the bench, then drive two screws into the end of each slat (see Figure A).
Put the benches in place flush with the back of the planter boxes (Photo 6). Screw the benches and planter boxes together with four 2-1/2-in. screws, then screw on the planter supports inside the planter box with three 2-1/2-in. screws each.
Level the planter boxes if necessary, adding hidden 2x2s or 2x4s for legs (Photo 7).
Step 3: Assemble the trellis
Photo 8: Attach the trellis posts
Attach the posts to the sides of the support blocks with three screws.Photo: Courtesy of We do everything by our own hands
Photo 9: Attach the top rails
Screw the right and left top rails to the posts. Mark the post spacing first to keep the posts plumb.Photo: Courtesy of We do everything by our own hands
Photo 10: Install the lattice
Mark the bottom edge of lattice on each post, then nail the lattice with siding nails.Photo: Courtesy of We do everything by our own hands
Screw support blocks to the backs of the planter boxes 3 in. in from the corners, then attach the posts (Photo 8). Cut the posts 7 ft. long plus the distance (if any) the planter box was shimmed up, so that they sit on the ground but are level with each other at the top. Drive two additional screws into the posts from the inside of the planter boxes, but don’t worry if the boxes are still a little wobbly—the top rail and cap lock everything together.
Set the top 2×4 rails on the ground next to the posts, leaving a 1-1/2-in. overhang at the outside ends. Mark the position of each post on the top rail, then clamp the rails flush with the top of the posts and fasten them with 3-in. screws to the posts and to each other (Photo 9).
Nail on the lattice, overhanging it 1-1/2 in. on the outside edges and butting the pieces at the corner (Photo 10).
Screw on the 2×6 cap pieces to finish the structure, mitering them at the inside corner and screwing the two sides together. Drop in the plastic planter boxes (from home centers or garden supply stores), fill with dirt, and plant with a mix of climbing flowers and vines.
Project PDF Files
Click the links below to download the construction drawings, materials list and cutting list for this project.
Required Tools for this Project
Have the necessary tools for this DIY project lined up before you start—you’ll save time and frustration.
- Circular saw
- Countersink drill bit
- Drill bit set
- Drill/driver - cordless
- Framing square
- Miter box
- One-handed bar clamps
- Paint roller
- Safety glasses
- Tape measure