Shop for materials
You can buy two types of garage door insulation kits at home centers. An R-8 vinyl-faced fiberglass batting kit provides a relatively high R-value. (Two examples are the ADO Products Single Garage Door Insulation Kit, No. 1611025, and Owens Corning Garage Door Insulation Kit, No. 500824.) It takes two kits to insulate a typical 16-ft.-wide garage door. Or you can buy precut R-4 expanded polystyrene (EPS) panel foam online (one choice is the insulated garage doors Kit from Cellofoam). Just cut each panel to length and bend and snap it into the horizontal rails on your door. However, at R-4 per inch, EPS has the lowest R-value. If you live in a moderate climate, that may be enough.
If you’re willing to do a lot of precise cutting, you can achieve a higher R-value, up to R-9.8 with 1-1/2-in.- thick foil-faced fire-rated extruded polystyrene (XPS). (Johns Manville CI Max and Dow Thermax are two brands.) Unfaced non–fire rated XPS rigid foam should not be used for insulated garage doors. It’s extremely flammable and when ablaze, yields toxic fumes.
Next, buy enough doorstop vinyl weather stripping to seal the top and sides of your garage door. You’ll also need new vinyl bottom seal to fit your existing track, or buy a new track if yours is damaged.
Insulated garage doors
Photo 1: Measure, mark and install the retainer pins
Measure to fnd the spot that’s 12 in. from each edge of the panel and midway between the horizontal rails. Mark the location. Then peel off the adhesive backing paper and press the retainer pin base onto the panel. Install two retainer pins in each panel.Photo: Courtesy of We do everything by our own hands
Photo 2: Cut the batting
Roll out the batting with the vinyl side down and mark the cutting lines. Place the batting on scrap plywood. Then compress the insulation with a straightedge and cut with a utility knife.Photo: Courtesy of We do everything by our own hands
Photo 3: Lock the batting in place
Line up the insulation so it’s centered in the panel and push it against the retaining pin until it punctures the vinyl facing. Then push the retaining cap over the pin until it snaps into place.Photo: Courtesy of We do everything by our own hands
We chose the R-8 fiberglass insulation kit from ADO Products for our door, so we won’t be showing you how to cut and install XPS foam panels in this story.
Start by washing each door panel with household cleaning spray and rags. Then rinse the areas with clean water and let dry. Next, install the retaining pins (Photo 1). Measure the height and width of each panel and add 1 in. to the length and width when you cut the batting to size for a snug fit (Photo 2). Panel sizes may differ along the door, so measure each one as you go rather than pre-cutting all the panels based on one measurement. Fit the cut insulation into the panel with the vinyl side facing into the garage. Then secure it to the retaining pins (Photo 3). Repeat until all the panels are insulated.
Mount the doorstop weather stripping
Photo 4: Test-fit the doorstop
Place the doorstop against the top and side jambs so the vinyl weather stripping is at a 45-degree angle. Temporarily secure it in place with nails pounded in only partway.Photo: Courtesy of We do everything by our own hands
Photo 5: Readjust to accommodate door movement
Apply pressure to the door to simulate the effect of a strong wind. Then move the doorstop inward to maintain a good seal. The gap may not be the same in every location along the sides, so check it in several spots and readjust accordingly.Photo: Courtesy of We do everything by our own hands
Starting at the top of the door, tack the doorstop weather stripping to the top jamb. Mount the side doorstops the same way (Photo 4). Then press against the door to simulate how much it might move in strong winds (Photo 5). Readjust the doorstop so it seals against the door even in windy conditions. Then pound the nails in all the way. If the door has too much play to adjust the doorstop properly, or you can see light through the doorstop weather stripping, replace your existing hinges with spring-loaded versions that press the door against the weather stripping at all times.
Install a new bottom seal
Photo 6: Uncrimp the bottom seal track slots
Jam a fat-blade screwdriver into the crimped area and twist to gently bend out the aluminum track. Repeat on each end of the track.Photo: Courtesy of We do everything by our own hands
Photo 7: Slide in the new bottom seal
Slather some dishwashing detergent onto the slots along the bottom track or spray them with silicone. Then insert the vinyl seal and pull it into place. Cut off the excess vinyl with a utility knife and crimp the ends of the track with a pair of pliers.Photo: Courtesy of We do everything by our own hands
Most steel doors have a track along the bottom to hold a vinyl seal. The vinyl can harden from sun exposure and crack or break off in sections, letting in cold air. Installers usually crimp the slots at each end of the track to retain the seal. Open the crimps (Photo 6) and slide out the old seal. Then install the new one (Photo 7).
Test the door
A properly balanced garage door should stay in place if you lift it part-way and let go. However, insulation adds weight to the door, and that may throw off the balance. If your door falls after you let go of it, hire a garage door service company to readjust the spring tension. Leaving the door in an unbalanced state can damage your garage door opener.