Check the Whole Wall Cavity With a Stud Finder
The Tools You Need
Once your hole is drilled, you can shove a glow rod through the hole, attach your wire to the eyelet at the end and pull it back through. Glow rods can also be used to hook wires to pull them out. As their name suggests, glow rods glow in the dark. This makes them easier to spot when you're working in dark areas (which is most of the time).
Glow rods come in various lengths and thicknesses, and you can combine as many sections as the job requires. Thinner rods flex more and work better when you have to make sharp turns. A thicker rod can span longer distances and is better for hooking wires that are more than a few feet away. A 9-ft. glow rod kit costs about $40 at home centers. Expect to pay about $60 for a 24-ft. kit.
Push Through More Than You Need
Hook on to a Flex Bit
Sometimes you don't need to use glow rods at all. Most flex bits have holes in the ends of them. If you have access to where the flex bit pops out, attach your wire directly to the bit and fish the wire through that way. Twist the wire and tape it up to make sure it doesn't come off when you're pulling it back through. Remove your bit from your drill before pulling so you don't accidentally spin the bit and twist up your wire.
Fish Wires Through the Holes for Recessed Lights
Protect Drywall With a Mud Ring
Mud rings are approved only for low-voltage wires like communication and coaxial cables. If you need to install a regular gang box for an electrical receptacle or wall switch, install the mud ring temporarily to protect the drywall while you fish the wire, then remove it.
Check out nine more tips for DIY electrical wiring.
Install Conduit Inside Cabinets
Invest In a Bumper Ball
Wires aren't supposed to be installed any closer than 1-1/4 in. from a penetrable surface (the outside of the drywall). That means you shouldn't be drilling holes right next to the drywall. But it's not always easy to control where a flex bit goes. A Bumper Ball flexible drill bit guide installed on the end of your flex bit will help maintain the proper space between the bit and the outside of the wall cavity. You can buy a set of two at electrical suppliers or at .
Hold on Tight
When hooking coaxial cable, just tape the whole wire to the glow rod. You'll never lose a light wire just using tape. Use the same technique when working with communication cable like phone wire. If you try to hook one of the small communication wires, you could stretch and damage that individual wire several feet down inside the sheathing.
Get a Better View With an Inspection Camera
You know your wire is in there somewhere, but you just can't seem to find it. It's probably hung up on another wire or pipe, but guessing isn't going to solve the problem. Instead, shine a flashlight onto an inspection mirror to find out exactly what's going on. This is a simple, inexpensive tip that can save you a lot of time and frustration. Pick up an inspection mirror at an auto parts store for less than $10. Or bump it up a notch and pay a few more bucks for a mirror with small built-in lights, so you can see exactly what's going on.
Don't Spin the Bit In Insulation
Keep Low-Voltage Wires Away From Electrical Cables
It's really tempting to fish low-voltage wires (like coax and Cat-5e) through existing holes occupied by electrical cables, but don't do it! Even though cables are insulated, the high-voltage current can interfere with the signal in the low-voltage wires. This could result in bad TV reception or unreliable phone and Internet service. Drill a new hole, and keep the new low-voltage wire several inches away from electrical cables. It's OK to run low-voltage wires perpendicular to cables, and it's also OK to run low-voltage wires next to electrical wires that are encased in conduit or metal sheathing.
Buy Extra Wire
Have plenty of extra wire or cable on hand, because it's not likely that you'll be able to fish a wire in a straight line from Point A to Point B. There's also the possibility that your wire might get hung up on something, and you'd have to abandon it and start over.
Identify Roughed-In Wires
If you're installing more than one wire, save yourself a lot of headaches by identifying the wires as you install them. It's a lot harder to figure out which wires go where when they're covered with drywall. The electricians we talked to use a “code” for marking wires, and so can you. Develop a system and write it down. You don't want to have to guess after you've gone through all the trouble of running the wires all around the house.