Overview: Solving unanticipated electrical problems
Replacing a light fixture is one of those DIY jobs that’s theoretically quick and simple, but often becomes a three-hour series of problems.
So we talked with two of our master electricians. They’ve seen—and solved—all of those frustrations and offered these tips to help DIYers through the job quicker and safer. We won’t show you here, but this article will walk you through step-by-step on How to Hang a Ceiling Light Fixture.
Flipping the breaker isn’t enough
Non voltage detector
You don’t have to actually touch a bare wire to check for voltage with this detector. Holding the tip on or close to the wire’s insulation is enough.
Even after you turn off the breaker that controls the light’s circuit, you can still get shocked. How? Some junction boxes contain wiring from multiple circuits. So even if you cut the power to the light fixture, there may still be live wires in the junction box. To be safe, check all the wires in the box with a non voltage detector before you disconnect any wires. Just touch each wire’s insulation with the tester. If the light glows, the wire is live.
Buy extra hardware
Extra mounting brackets
Buy various types of mounting brackets in advance in case the one supplied with the fixture doesn’t work.
The mounting brackets supplied with your fixture may not work with your junction box. So when you buy your new fixture, also pick up a few other styles of mounting brackets. Better to spend an extra five bucks than to make a trip to the hardware store in the middle of the job.
Slick solution for long screws
Wire stripper/bolt cutter
Shorten long screws without ruining the threads with a special bolt cutter, which is often a feature on a wire stripper.
If the fixture mounting screws are too long to fit in the box, you’ll need to cut them. A hacksaw works but makes a mess of the threads. A wire stripper with built-in bolt cutters is the way to go. Just thread the screw into the correct size threaded hole until you get the length you need and squeeze the handle. As you remove the screw, the tool cleans up the threads at the cut end. Get one at a home center for about $10.
Short wires, no problem
Extend short wires
Extend short wires with extra wire connected with stab-in connectors of the proper size.
When the wires in the box are too short, making connections is aggravating. You’ll want to hunt down whoever installed them and throttle that person. But instead, just go to a home center and pick up a few stab-in connectors. In tight spaces, they’re much easier to use than twist-on nuts. Push a “pigtail” (a new piece of wire) into the connector, then push the connector onto the old wire. Presto! You’ve got plenty of length to connect to the fixture’s wires. Make sure the wire you use for the pigtail is the same gauge as the existing wire.
Aluminum Wiring Caution
If you have aluminum wiring, don’t work on it yourself. The connections require special techniques. Call in a licensed pro who’s certified to work with it. For more information, go to http://www.cpsc.gov/cpscpub/pubs/516
Extend the box
Add a box extender when the old box is behind the wall surface more than 1/4-in.
If the junction box is recessed more than 1/4 in. from the surface of the wall or ceiling, you’ve got a code violation. This is common when a layer of drywall or wood was installed over the original ceiling. To correct it, add a box extender (about $2). If you don’t find one for round or octagonal boxes at home centers, search online.
Use a third hand
Improvise an extra hand
Bend a scrap of wire to support the fixture while you wire it.
Connecting a fixture takes three hands: one to hold the fixture and two to make the connections. If you don’t have a third hand, hang the fixture from a scrap of wire or a coat hanger while you make the connections.
Probe for the screw hole
Aligning a screw hole
Align the screw hole with a thin screwdriver.
Many fixtures have a canopy that’s held in place by two screws. Aligning the first screw is easy enough because you can tilt the canopy a little and aim for the screw hole above it. To align the second screw, stick a skinny screwdriver or a nail into the canopy hole and rotate the canopy until you find the screw hole.
Check your home wiring before you buy the fixture
If your home was built before 1985, beware: Many new light fixtures can’t be connected to pre-1985 wiring because the insulation on the wiring can’t withstand the heat generated by the fixture. These fixtures carry a warning on the label: “Use wire rated for at least 90 degrees C.” If you know your wiring was installed before 1985, you’ll have to choose a fixture that doesn’t carry this warning. Hanging fixtures, for example, usually don’t require newer wiring because they don’t heat the wiring as much as fixtures that mount directly against the ceiling. The alternative is to replace the wiring, which may be a small job, or huge, depending on the situation.
If you don’t know the age of your wiring, look at the fine print. If you have plastic sheathed cable (Romex is one common brand) and can see the outer sheathing, look for “NM-B” or “UF-B.” Or look for “THHN” or “THWN-2” on the insulation of individual wires. If you see any of these, the wiring can handle the heat.
Buy better connectors
Buy connectors with internal metal threads for more secure connections.
The twist-on connectors supplied with most fixtures are all plastic; no metal threads inside. They just don’t grip the wires for an easy, secure connection. So spend an extra few bucks on a pack of assorted small connectors with metal threads when you buy the fixture.
Make a strong connection
Connecting stranded wire to solid wire
Extend the stranded wire further into the connector than the solid wire for a solid connection.
Light fixtures almost always require a connection between solid wire and stranded. That’s frustrating because the connector twists and pushes the stranded wire but doesn’t grab it. Here’s the solution: First, cut off the old exposed solid wire and then strip off 1/2 in. of the insulation. On the stranded wire, strip off 5/8 in. Hold the wires together so the stranded wire extends about 1/8 in. beyond the solid wire and twist on the connector. The end of the stranded wire will bunch up inside the tip of the connector, locked in place for a secure connection.
Why work in the dark?
Carry your flashlight on your head so you don’t have to fumble around in the dark.
If the light fixture and outlets in the room are on different circuits, plug in a couple of lamps before you shut off the power to the fixture. Otherwise, strap on a camping headlamp. You’ll find them everywhere, some for less than $10.
Stripped hole fix
Tapping a stripped hole
An electrician’s tap cuts new threads so you don’t have to replace the box. You’ll need a bigger screw.
The built-in screw holes on a metal box are easy to strip. And if that happens, your first impulse might be to use a drywall screw. Bad idea—the sharp tip can poke through wire insulation. Instead, use an electrician’s tap (about $9) to cut new threads in the hole. That will enlarge the hole from a No. 8-32 screw size to a No. 10-32, so you may need a couple of new screws, too.
Check for ground
Checking for ground
Touch a circuit tester to the ground wire and the hot wire to test the ground. If it lights, the ground is good.
Your new light fixture will have a ground wire (green coated or bare copper). But if you have an older metal box, there may not be a ground wire inside the box to connect to. Adding a ground wire to the box isn’t difficult; just connect a 6-in. section of bare copper wire to the box by driving a No. 10-32 ground screw (available at home centers) into a threaded hole in the box. But before you do that, you have to make sure the box itself is grounded.
Here’s how: turn the power on and make sure the light switch is turned on. Find the hot wire (typically black or red) using your non voltage tester. Next, you’ll need a circuit tester (about $4 at home centers). Touch one of the tester’s probes to the bare end of the hot wire and the other to the box. If the light glows, the box is grounded. If not, a ground wire will need to be run to the box to meet electrical code. That’s a job for a licensed electrician, unless you’re a very knowledgeable DIYer.
Chandelier chain too long? There’s a tool for that!
This special tool neatly opens and closes decorative chains.
Raising a chandelier is as easy as removing a few chain links. But opening and closing links without scratching or misshaping them can be a pain. That’s why some whiz kid invented chain pliers. This tool bends links open and closed gently and neatly. Search online for “Westinghouse 70099” (about $20). Sure, it’s a splurge, but don’t you want a tool none of your buddies have ever seen?