Wiring a GFCI plug receptacle
Photo 1: Remove the outlet
Turn off the power at the main circuit panel and remove the old outlet. Disconnect the wires by clipping them close to the outlet.Photo: Courtesy of We do everything by our own hands
Photo 2: Strip the wires
Strip the insulation from the wires to expose the amount of wire shown on the stripping gauge located on the back of the GFCI plug receptacle. Connect the hot and neutral wires that provide power to the “line” terminals of the GFCI plug. The terminal for the neutral wire will be marked “white” or “neutral.”Photo: Courtesy of We do everything by our own hands
Photo 3: Connect other outlets
Remove the tape covering the “load” terminals and connect the wires leading to another outlet or outlets to these terminals. Again, the white neutral terminal will be marked. Fold the wires back into the box and screw on the GFCI receptacle and cover plate.Photo: Courtesy of We do everything by our own hands
Photo 4: Label the outlets
Attach the “GFCI-protected outlet” label to downstream outlets. Test the downstream outlet by plugging in the GFCI tester and pressing the test button. The lights on the tester should go out. Press the reset button on the GFCI to reenergize the outlet.Photo: Courtesy of We do everything by our own hands
GFCI outlets reduce the danger of deadly shock from faulty plug-in cords and devices. A GFCI (ground fault circuit interrupter) is a special type of outlet that detects dangerous ground faults and immediately turns off the power to stop shocks. You can replace almost any electrical outlet with a GFCI outlet. Correctly wired GFCIs will also protect other outlets on the same circuit.
While it’s common to find GFCI outlets in bathrooms and kitchens, the electrical code also requires GFCIs in unfinished basements, garages, most outdoor receptacles and places where construction activity occurs. We’ll show you how to replace a standard duplex receptacle with a GFCI and wire it to protect other outlets. (For more information about wiring outlets, see Wiring Switches and Outlets).
You’ll need a screwdriver, a wire cutting and stripping tool, and an inexpensive voltage tester. We also recommend you add a GFCI tester to your tool drawer. GFCI testers are available at home centers and hardware stores and are a handy device for troubleshooting standard outlets as well as GFCIs.
Before you start, locate the circuit breaker or fuse that controls the outlet you plan to replace and shut off the power to the circuit. Plug a lamp, radio or the GFCI tester into the outlet to test for power and make sure it’s off. Then unscrew and pull out the old outlet and count the number of wires in the box. Calculate the minimum box size required for all of the wires plus the GFCI (see “Required Box Size,” below). If the existing box is large enough, follow the steps in Photos 1 – 4 to replace the outlet with a GFCI. Replace an undersized box with a new one of adequate size. (For more information on box replacement, see What You Should Do With Crowded Electrical Boxes).
Using a GFCI to protect additional outlets on the same circuit breaker or fuse can be tricky. Don’t do it unless you know exactly where the wires go. In the workshop, we had the advantage of being able to visually trace the wires.
Test all the GFCIs in your house at least monthly by pressing the test button or using your GFCI tester. If an outlet fails to trip, replace it with a new one.
Required Box Size
To figure the minimum box size required by the National Electrical Code, add:
1 – for each hot and neutral wire entering the box
1 – for all of the ground wires combined
1 – for all of the cable clamps combined (if any)
2 – for each device (switch or outlet—but not light fixtures)
Multiply the total by 2 for 14-gauge wire and 2.25 for 12-gauge wire to get the minimum box size required in cubic inches. Plastic boxes have their volume stamped inside. Steel box capacities are listed in the electrical code.
Required Tools for this Project
Have the necessary tools for this DIY project lined up before you start—you’ll save time and frustration.
- 4-in-1 screwdriver
- Electrical tape
- Needle-nose pliers
- Non- voltage tester
- Utility knife
- Voltage tester
- Wire stripper/cutter
Required Materials for this Project
Avoid last-minute shopping trips by having all your materials ready ahead of time. Here’s a list.
- Electrical boxes
- Electrical cable
- GFCI outlet
- Wire nuts
- Wire staples