Size Up Your Leaky Door
Photo 1: Tighten the hinges
Lift the door by the doorknob to check for loose hinges. If the door moves upward, tighten the top hinge screws. That might solve the draft problem!
Feeling a winter chill? If you run your hand around the perimeter of your closed door and feel a cool draft, your door weather stripping is probably worn, cracked or deformed.
Maintaining an airtight seal on your doors is essential for stopping cold drafts and keeping your home comfortable. Replacing door weather stripping on newer doors is fairly easy. You can usually slide out the old door weather stripping and push or slide new vinyl or foam weather strips into the grooves in the door or the surrounding frame. The biggest hassle is finding replacement door weather stripping that matches. However, older doors were made without integral weather stripping and it must be added.
Installing new door weather stripping on older doors (and doors for which you can’t find replacement door weather stripping) is fairly easy, and we’ll show you how to do it in this article. Door weather stripping kits are available at most full service hardware stores and home centers. They include two side weather strips, a top weather strip and fasteners.
We decided not to replace the old, worn bronze weather stripping on our door with new bronze because the project is difficult, especially around the latch plates. (You can still find several types of replacement bronze at full-service hardware stores.) The wrapped foam type shown here is easier to install and more effective. We later painted the wood flange to blend with the frame. Before you go out to buy your materials, check the door to make sure the draft isn’t caused by loose hinge screws (Photo 1). If the screws no longer bite, you may have to glue wood plugs in the holes and re-drive the screws.
How to Buy Weather Stripping for Doors
You can usually find the types of door weather stripping shown here at well-stocked hardware stores and home centers. Many other types are available, but you’ll probably have to order them from a catalog. Ask to see a catalog at your local hardware store and order through the store if possible.
We like the wrapped foam type (A and B, shown at right). It’s durable, retains its shape, withstands abrasions and conforms to a wide range of gaps. The metal flange with slots for screws (B) is a bit more adjustable than the nail-on wood flange type (A). The vinyl or silicone bulb type (C) won’t cover wide gaps as well as wrapped foam, but it has a smaller profile with a cleaner look.
Finding new door weather stripping to match the exact profile of the old can be difficult. If you know the door manufacturer or where the door was purchased, try there first. (Check the door and frame for a label.) Otherwise, call a local door or window repair service. (Look under “Doors, Repair” or “Windows, Repair” in your Yellow Pages or online.) It may stock the materials or tell you where to call. Replacement kits for the wrapped foam and magnetic (for steel doors) types are sometimes available at hardware stores and home centers.
Cut and Nail the Weather Stripping
Photo 2: Measure the jamb
Close the door and measure the top of the frame from side to side. Mark the length on the short section of your purchased door weather stripping with a clear, sharp line.
Photo 3: Cut the top piece
Cut the foam part of the door weather stripping with a sharp scissors. Then cut the wood flange with a hacksaw or other fine-tooth saw.
Photo 4: Nail the top piece
Tap 1-1/2 in. nails into the wood flange and position the weatherstripping so the entire length of the foam seals against the door. Tack the door weather stripping in place but don’t drive the nails home yet. Then measure the length of the sides of the frame.
Photo 5: Cut the side pieces
Cut one end of each side door weather stripping to fit the profile of the top piece. Mark the profile using a scrap for a guide, cut the foam with a scissors and cut the profile with a coping saw.
Photo 6: Adjust the cut
File or sand your cut for a tight fit. Then measure and cut the bottom to length (Photo 3). Position the door weather stripping so that the entire length seals to the door and tack it in place.
Photo 7: Test the fit
Open and close the door several times to make sure the door weather stripping seals against the door and the door latches and locks. Adjust the door weather stripping as needed. Drive the finish nails home.
The door weather stripping kit will come with two long pieces for the side jambs and a short piece for the top jamb. Begin with the top and follow Photos 2-7 for the basics. Make precise measurements and cuts so you get nice, airtight fits (Photos 2 and 3).
Position the nails about 2 in. in from each end (to avoid splitting), and space others about every 12 in.
The key to positioning the new door weather stripping is to shove it against the door so it compresses slightly along its entire length (Photo 4). If you compress it too much, the door won’t latch when you close it, a common rookie mistake.
The “coped” cuts on the side jambs make a clean, tight joint (Photo 6). Make this cut first, leaving plenty of length for the bottom cut.
It’s critical to make sure that the door shuts and latches easily before you drive the nails home (Photo 7). However, the door weather stripping also needs to fit snug to the door over its full length. For small adjustments, pull the nails and start them in a new spot, or loosen the screws if you’re using metal door weather stripping.
When you paint the wood flange, keep the paint off the foam.
How to Install a Door Sweep
Photo 8: Measure for a door sweep
Measure the width of the door from inside and mark the length on your new sweep.
Photo 9: Cut the door sweep
Cut the flexible flap with a sharp scissors or sharp utility knife. Then cut the flange with a hacksaw.
Photo 10: Position and mark holes
Position the door sweep with the flexible portion lightly touching the top of the threshold. Then mark the screw positions and drill the pilot holes.
Photo 11: Attach the sweep
Push the sweep down against the threshold and drive the screws. Open and close the door to test the seal.
Photo 12: Seal the bottom corners
Cut two 2 x 1-3/4-in. pads from 1/8-in. thick felt. Nail the pads at the bottom of each side frame as shown. Open and shut the door and adjust the pads if necessary.
Shut the door, then look for daylight and feel for a draft coming under the door. If you see a lot of light or feel a draft, install a new door sweep.
Our door had old bulb-type door weather stripping attached to the threshold. While these types can be effective, you have to replace them every few years because foot traffic wears and crushes them.
Door sweeps last longer, but won’t always work if they brush or rub against the floor or carpet when you open the door. If the floor, carpet or rug is even with or higher than your threshold (the bottom of the door frame; Photos 8 and 11), you can’t use a sweep.
For a replacement, we chose a simple face-mount door sweep with a flexible vinyl flap because it’s easy to mount and adjust. Photos 8 – 11 show you how to measure, cut and screw it to the door.
You’ll be left with a pair of small gaps between the door weather stripping on the frame and the sweep, at the bottom corners of the door. Unless you want a perfectly airtight, draft-free door, don’t worry about these gaps. However, Photo 12 shows one way to close them. It’s not precise; use whatever thickness of felt (or combination of layers) fits between the door and frame without hindering the door operation.
Good work! You can look forward to a more comfortable winter.
Replace Threshold Weather Stripping
Old door weather stripping bulbs on door thresholds need to be replaced when they get torn or worn down. After pulling out the old vinyl door weather stripping, take a large nail or nail set and clean out any crud in the grooves. This will make the new door weather stripping slip in much easier. Carefully measure and cut your new vinyl piece to length between the door jambs.
Start at one end of the threshold and press the flanges of the new door weather stripping into the grooves. Use a hammer and wood tapping block, if necessary, to drive the flanges all the way down into the threshold grooves.
Video: Garage Door Weather Stripping
Required Tools for this Door Weather Stripping Project
Have the necessary tools for this DIY project lined up before you start—you’ll save time and frustration.
- Coping saw
- Cordless drill
- Nail set
Required Materials for this Door Weather Stripping Project
Avoid last-minute shopping trips by having all your materials ready ahead of time. Here’s a list.
- Door sweep
- Vinyl bulb for door sill
- Weatherstrip kit