A dry basement is a useable basement
Installing a drain system is filthy, backbreaking work, but it’s not complicated. With a little instruction from our drain tile experts, you can do a first-class job. And DIY pays off big: Pros charge $5,000 to $8,000 for a typical job (120 linear feet of drain tile). You can install yours for less than $1,500 in materials and tool rentals.
Meet the experts
Rite-Way Waterproofing has been in the business of installing waterproofing basement drain systems since 1965. The pros there know what works, and they’d better, because the company has installed 100,000 systems, each with a lifetime guarantee. They also know what doesn’t work—half of Rite-Way’s current jobs involve replacing failed systems installed by other contractors.
A drain tile system creates a perfect pathway for dangerous radon gas to escape. If you’ve never tested for radon, it’s smart to do so before you install a drain system. That way, you can plan for a radon mitigation system as well.
Before you get started
It’s always best to stop water from entering your basement in the first place, so before you run to the rental center for your jackhammer, be sure to address the exterior issues. The grade next to the house should slope down away from the building by least 6 in. for the first 10 ft. Consider installing gutters, or make sure the existing gutters are working properly. And check that your irrigation system isn’t adding to the problem by spraying water right up against the side of the house.
If your waterproofing basement is finished, with stud walls and insulation covering the foundation walls, you can still install a drain system. When you break out the concrete, leave small sections of floor intact so the wall doesn’t drop down. A 4 x 4-in. section every 6 ft. is enough to support the wall. If there are obstacles along the wall (like a furnace), plan to tunnel under them. You’ll find most of the materials you’ll need at a home center. Order the rock from a landscape supplier. You’ll also need a pickup to haul the dirt to the landfill.
Always check with your local building official. Explain your project, and see if any permits or inspections are required in your area. Sometimes, a building official who has been around for a while may have information on how your house was built or what issues you may run into in your area.
Control the dust
Photo 1: Get ready for dust
Instead of just covering your stuff with sheets of plastic, isolate your work area with a wall of plastic sheeting. Make sure to fill in the spaces between joists.
There’s no getting around it: Busting up concrete is a dirty job. Shut down your furnace or central air conditioning while you’re working, and cover all return air vents until you’re finished cleaning up. Instead of covering your furnishings with plastic, move everything out of the area and drape plastic from the ceiling to create an isolated work space (Photo 1). If you have an unfinished ceiling, be sure you run the plastic up into every joist space. Set a fan in the window to exhaust the heavy dust while you run the jackhammer. And wear a dust mask and hearing protection.
Bust up the floor
Photo 2: Bust up the floor
Remove 16 in. to 18 in. of concrete along the wall with a rented electric jackhammer. Start by chipping in a straight line along the entire length of the wall, then come back and bust it into manageable chunks.
The pros use electric jackhammers, because the air that runs pneumatic jackhammers kicks up a lot more dust. You can get one from a rental center for under $100 a day. Start by hammering a line about 16 in. to 18 in. away from the wall (Photo 2).
Once the perimeter is done, come back and break the row of concrete into manageable chunks. Each section will break free easier if it has room to pull away, so remove the sections as you go. If you’re working alone, make the most of your rental time; just set the chunks aside until you’re done with the hammer. Don’t forget to bust up a larger area for your sump basin.
Dig the trench
Photo 3: Dig a trench along the wall
Dig the trench as deep as the bottom of the footing. Instead of lugging pails of soil up the stairs, buy buckets that will fit through your basement windows.
Once the concrete is removed, dig down to the bottom of the footing but not below. If you compromise the soil under the footing, you could end up with cracks in your wall, or worse.
Five-gallon buckets are OK for hauling out debris, but the guys at Rite-Way use rubber feed buckets (typically used for farm animals) because they fit through small basement windows and are less likely to bang up trim (Photo 3). You can get them at farm supply retailers for under $20. And when it’s time to haul the debris away, you may find that the landfill considers it to be “clean fill.” You may be able to dump it for free!
Install the basin
It’s best to locate your basin in an unfinished area of the basement so you can have easy access to the sump pump. If you never plan on finishing the basement, locate the basin in the same area where you want the water to drain out of the house so you don’t have as much plastic pipe to install. Dig the hole so the top of the basin will sit flush with the finished concrete.
Many basins come with flat “knockout” areas meant to make cutting the hole easier. Don’t assume the location of these knockouts will work for your system. Because the pipe will be slightly sloped down toward the basin, the longer the drain is, the lower the pipe will be when it reaches the basin. You never want standing water in your drainpipes, so make sure to choose a model that is deep enough. Our experts typically use 30-in.-deep basins. They use 36-in.-deep models for systems longer than 120 ft., and they install two basins if the drain is longer than 180 ft.
Set the basin in place, and then mark the locations for the holes where the pipes will meet the basin. Keep in mind there will be a thin layer of rock (one layer thick) under the pipe near the basin. Cut the holes using a reciprocating saw, jigsaw or hole saw. The holes don’t have to be perfect.
Don’t haul out all the dirt right away; you’ll need some to fill in around the basin. Once it’s permanently in place, fill in around it, tamping the dirt with a 2×4 as you go.
Caution: Never drill holes in the bottom of the basin! If you have a high water table, water could come up from the bottom, and your pump will run nonstop, attempting to dry out the neighborhood.
Drill holes in block
If your waterproofing basement walls are made from concrete block, drill 1-in. holes in each block core and into each mortar joint (see Figure A). This will allow the water that collects in the cores and between the blocks to flow into the drain. Drill the holes as close to the footings as you can. You may find that the bottom blocks are filled with concrete. In that case, you’ll have to remove any existing walls and install foundation wrap. Cut down on dust by laying a shop vacuum hose next to the hole as you drill.
Install the pipe
Photo 4: Lay in the pipe
Lay the pipe with the holes face down. Add or remove rock to slope the pipe so water flows to the sump basin. There’s no need to cement the pipe connections.
Before you lay the pipe in the trench, shovel in a bottom layer of 1-1/2-in. to 2-in. washed river rock (a layer of smaller rock can become clogged with minerals and sediments). The pipe should slope toward the basin at least 1/4 in. for every 10 ft. Rake the rock around to achieve this pitch.
Lay your irrigation pipe on top of the rock. Don’t use ordinary flexible drainpipe because it clogs easily. The pros prefer to lay down a 4-in.-diameter Schedule 10 perforated pipe. Buy the kind of pipe with rows of 1/2-in. perforation holes only on one side, not all around the pipe.
Lay the pipe with the holes facing down (Photo 4), so the minerals and sediment in the water can flow down around the pipe and settle into the ground. This way, the water that does rise up into the pipes from underneath will be relatively clean. Clean water will add years to the life of the whole system. Start at the basin, and push the male end of the pipe into the basin about 4 in. Use PVC or ABS elbows at the corners. It’s not necessary to cement the sections together.
Divert the water into the drain
Photo 5: Install hose in the block walls
Drill 1-in. holes in each block core and each mortar joint. Then insert sections of 1-in. irrigation hose from the holes into the gravel to carry away the water.
Once your pipe is installed, it’s time to install the 1-in. irrigation hose that will carry the water from the blocks to the trench (Photo 5). Softer hose, like garden hose, can get crushed flat by the new concrete, so stick with irrigation hose. Cut the hose with a hacksaw or reciprocating saw. Make sure each section of hose runs several inches past the footing.
If you have a solid concrete foundation
If you have poured concrete walls rather than block, you’ll need to install a foundation wrap to let the water into the drain as shown below. Foundation wrap is made from tough plastic and consists of rows of dimples that allow water to flow behind it. Platon by CertainTeed is one example. Home centers can order it if they don’t stock it.
Cut the sheets into strips with a utility knife. Bend the strips at 90 degrees and let the bottom half run past the footing. The length of the wrap that’s up against the wall depends on your situation. At a bare minimum, run the wrap up 4 in. above the top of the concrete on a poured wall, or up 4 in. past the holes you drilled in the block wall. If you’re working along stud walls, try to tuck the wrap behind the bottom plate.
Cover it back up
Photo 6: Cap off the trench with concrete
Lay plastic over the rock and cover it with concrete. Smooth out the concrete with a float. Wait 20 minutes, and work it smooth with a steel trowel.
Once the hoses are in or the foundation wrap is in place, it’s time to cover it up. Fill in the trench with river rock up to the bottom of the existing slab, and then cover the rock with at least a 6-mil thickness of plastic for a vapor barrier (Photo 6).
To cut down on dust, mix your concrete outside. Bagged concrete mix for slabs and sidewalks works just fine. Slide a 3-ft. section of 2×4 along the floor to “screed” the new concrete flush with the floor, and then smooth it out with a hand float. Wait 20 minutes, then smooth it with a finishing trowel. Use the float to completely fill the gap under any existing walls.
Hook up the pump
Pros prefer submersible pumps that have a vertical float switch on them because they’re more reliable than pedestal or float switch pumps. Install a 6- to 8-in. section of pipe on the pump, then a check valve. Make sure the check valve doesn’t interfere with the pump switch. Above the check valve, attach another section of pipe long enough to reach above the top of the basin.
Drill a 1/4-in. to 3/8-in. vapor lock release hole in the section of pipe that’s just below the check valve (see Figure B). This allows the pump to get up to speed before trying to force open the check valve, which may have many gallons of water pressing down on it. Angle the hole so water sprays down while the pump is working. It’s best if you have a dedicated outlet for your pump. Extension cords get unplugged, and other appliances hooked up to the same circuit could trip a breaker.
The pipe that exits the basement needs to be located in an area that slopes away from the house. If that means running a pipe back across the basement, consider burying the waste pipe in the trench and having it come back up where you want it. If your pipe is going to discharge above grade and you live in a cold climate, run the pipe no more than 8 in. past the siding. This will keep it from freezing up in the winter.
With few exceptions, basement drain water cannot be dumped into city sewer systems. Most systems can be drained into storm sewers as long as they’re above grade when they do. Ask your building official what the rules are in your area.
Required Tools for this Project
Have the necessary tools for this DIY project lined up before you start—you’ll save time and frustration.
- Chalk line
- Cold chisel
- Dust mask
- Extension cord
- Hammer drill
- Knee pads
- Knockdown knife
- Reciprocating saw
- Safety glasses
- Shop vacuum
- Tape measure
Required Materials for this Project
Avoid last-minute shopping trips by having all your materials ready ahead of time. Here’s a list.
- 30- to 36-inch-deep sump pump basin
- 4-in.-diameter Schedule 10 perforated pipe
- Concrete mix
- Duct tape
- Irrigation hose
- Irrigation pipe
- Masking tape
- River rock
- Sheet plastic
- Sump pump