Proper sharpening technique with the angle grinder
Photo 1: Safety precautions before starting
Pull the wire from the spark plug. Remove the gas cap, put a piece of plastic over the opening and replace the cap. This will help prevent gas spills when you flip the mower to access the blade.
Photo 2: Remove the blade
Clamp a block to the lawn mower skirt to stop the blade from spinning while you unscrew the nut. Use the longest wrench you can find to loosen the nut. It’s likely to be very tight.
Photo 3: Make light passes
Grind the blade carefully with an angle grinder to remove nicks and dents and restore the edge. Make several light passes to avoid overheating the blade.
Photo 4: Balance the blade
Balance the blade on a nail after you’ve sharpened both edges. If one side is heavy, it’ll drop. Mark the heavy side so you’ll know which end to grind. Grind a little off the heavy side and hang the blade on the nail again to recheck it. Repeat this process until the blade hangs level.
You wouldn’t take care of grass that’s too long by tearing off the end of each blade, would you? But that’s exactly what a dull lawn mower does, leaving the torn grass vulnerable to sun damage and disease. You could sharpen your mower blade with a file (it takes forever!), a rotary tool or a bench grinder, but we’ll show you how to do the job with an angle grinder. It’s fast and easy. If you don’t own a grinder, they don’t cost much to buy and can be used for all kinds of other tasks too.
To sharpen your lawn mower blade, you’ll need a socket or wrench to fit the blade nut. Tough nuts may call for a breaker bar and/or a penetrating lubricant. You’ll also need two clamps, a block of wood and, of course, an angle grinder with a metal grinding blade.
Start by disconnecting the spark plug wire (Photo 1). Next, place a piece of plastic (a sandwich bag works well) under the gas cap to prevent gas from leaking out of the vent hole when you tip the mower. Tip the mower so the side with the carburetor faces up.
Clamp a 2×4 block to the side of the mower to keep the blade from turning while you loosen it. Mark the “grass side” of the blade so you don’t reinstall it upside down. Use a socket wrench or a breaker bar to turn the nut counter-clockwise to loosen it (Photo 2). If it’s stubborn, soak it with penetrating oil for a half hour and try again.
Clamp the blade securely in a vise or to the edge of your workbench. Prepare for grinding by putting on your gloves, face shield, hearing protection and a long-sleeve shirt. Before you start grinding, hold the grinder against the blade and tip it up or down until the grinding disc is aligned with the angle on the blade. Try to maintain this angle as you grind. Keep the grinder moving and apply only light pressure so you don’t overheat the blade or grind away too much (Photo 3). If you overheat the metal, it’ll turn dark blue or black and become brittle. Then it won’t hold an edge. Your goal is to remove the nicks and dents and create an edge that’s about as sharp as a butter knife. A razor-sharp edge will dull quickly and chip more easily.
Make several passes across the blade with the grinder, checking your progress frequently. You don’t want to grind off more than necessary. If your blade has a lot of nicks and gouges, try this. Start by holding the grinder at a right angle to the blade and grinding the edge of the blade flat to remove the nicks. Be careful to use light pressure and move quickly. It’s easy to burn the thin edge. After you’ve removed the nicks, go back to grinding at the correct blade angle.
If your blade has deep nicks or is cracked, bent or worn thin, don’t sharpen it; buy a new one. You’ll find the best selection at stores that sell and service lawn equipment. Take the old blade with you to get an exact match.
If you don’t grind away the same amount of metal from both sides, the blade can become unbalanced. You can buy a special blade-balancing cone or simply hang the blade on a nail (Photo 4). Correct an unbalanced blade by grinding a little metal from the blunt end of the heavy side of the blade until it balances on the nail. Make sure the marked side is toward you when you reinstall it and that you tighten the nut securely.
Video: How to Sharpen a Lawn Mower Blade
A sharp lawn mower blade will help keep your grass healthy. Jeff Gorton, an editor at We do everything by our own hands, will show you how to sharpen a lawn mower blade so you can keep your lawn in great shape.
Required Tools for this Project
Have the necessary tools for this DIY project lined up before you start—you’ll save time and frustration.
- Angle grinder
- Safety glasses
- Wrench set
Required Materials for this Project
Avoid last-minute shopping trips by having all your materials ready ahead of time. Here’s a list.
- Block of wood
- Plastic bag